La-crosse-technology WS-2317 Bedienungsanleitung

1 Operation Manual Professional Remote Weather Station Table of Contents Page 1. Introduction ...

10433MHz transmission and will result in higher power consumption. Batteries will have a shorter life span for cable connection compared to using 43

11simply press and hold the PLUS (+) key for 2 seconds and a short beep will sound to synchronize the base station to sensors. Without being synchro

121. Low battery indicator 2. WWVB radio controlled time icon 3. Date display 4. Time zone display 5. Date, seconds, alarm time and time zone 6.

13LCD. In this case, check that all cables are correctly inserted into the correct sockets and/or check the batteries in the outdoor thermo-hygro se

14 NOTE: For reception of WWVB time/date signal, do not mount the base station closer than 5 feet from a computer, florescent lights or other electri

15 For accurate results, the rain sensor should be securely mounted onto a horizontal surface about 2-3ft above the ground and in an open area away f

16To wall mount, use the 2 screws to affix the wall bracket to the desired wall, plug in the thermo-hygro sensor to the bracket and secure both parts

17Time zone -5 ET Alarm time 12:00 am Relative air pressure 29.91 inHg Weather-picture threshold 0.09 inHg LCD contrast level 5 (1-8 levels) Rain

18Sunny Rainy Cloudy 11. Function Description of the Weather Station After setting up, the following data will be displayed in different sections

19Notes to inHg sensitivity setting for weather forecasting: The inHg pressure sensitivity can be set to suit the user’s requirement for weather fore

2 1. Introduction Thank you for purchasing this Professional Remote Weather Station. Designed for everyday use, the weather station will prove to

20- Outdoor dew point - Rainfall 24h - Rainfall 1h - Rainfall total. Notes to Dewpoint and Windchill: Air can at a certain temperature only carr

2112. Operation keys The base station has 8 keys for easy operation. Please refer to the following table for use and function of each key: Further

22- Wind speed - Wind direction - Wind direction display in degrees ALARM - key - In normal mode to enter the alarm programming mode - In alarm

23key enable/disable the buzzer alarm (long pressing) - To decrease the values in the setting modes - In basic programming mode audible storm alarm

2412. Storm warning sensitivity setting 9, 12, 15, 18, 21, 24, 29 inHg (default 9 inHg) 13. Audible storm alarm On/OFF (default ON) To change any

25received. Now press the MIN/MAX key to toggle from the minimum and maximum readings and the time and dates the records were received are also show

26rainfall total value to zero and the time recording to current time.  The second case is Rainfall 24h or 1h, which records maximum rain count onl

27Time alarm setting 1) Press the ALARM key to enter the normal time alarm 2) Press and hold the SET key to enter the alarm hour time set mode (the

284) Press ALARM key to confirm and press the MIN/MAX key to return to the normal display mode or press the ALARM once more to toggle to the outdoor

294) Press ALARM key to confirm and press the MIN/MAX key to return to the normal display mode or press the ALARM key once more to toggle to the out

3 This weather station is designed to work easily with your PC, simply connect and disconnect the PC cable at any time. System Requirements for PC u

30key once more to toggle to the dew point low alarm set mode. 5) Press and hold the SET key to enter the dew point low setting values (digits will

31key once more to toggle to the pressure low alarm set mode. 5) Press and hold the SET key to enter the pressure low setting values (digits will st

32Storm warning alarm setting Unlike the other weather alarms, the storm warning alarm is set by entering the main manual setting mode as follows: 1)

33values against the MIN/MAX values reached. To deactivate the general weather alarm icon, press the ALARM key. Important When entering the alarm se

34Rainfall 1h 0.0 inch 39.37 inch Wind 0.0 mph 111.8 mph Hysteresis To compensate for fluctuation of the measured data, which may cause the weat

35• Weather picture threshold • Storm warning threshold • LCD contrast • Alarm time • Weather Alarm thresholds • State of alarms (enabled/disab

36Note: It is important to keep all the connected extension heads away from rain, moisture and other extreme weather conditions as exposure can cause

3719. Interferences and problems with operation Problem & cause Remedy Distance between transmitters and receiver too long. Reduce distance be

38Quite frequently interferences are only of a temporary nature and may be easily overcome. If there are wireless headsets, remote babysitters or oth

39- Do not clean the funnel with the bottom half of the rain sensor attached nor the bottom part itself under running water. This may bear the dange

4 • Weather tendency indicator • Storm warning alarm • EL back light • Simultaneous display of all weather data with individual settings by the u

40With cable connection for data transmission: Measuring interval thermo-hygro sensor : 8 seconds Indoor data Pressure/ temperature : 4 times

23. Warranty Information41La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing defects in materials an

42LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION

FCC DISCLAIMER This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not c

5 this instruction manual, the manufacturer and supplier cannot be held liable. • For reasons of safety and operation, alterations to this device

6 4. Packaged Contents Before setting up, carefully unpack the contents onto a table or flat surface and check that the following are complete: It

7 Heavy weather PC software CD-Rom format (English version only) • 6.5ft PC cable for PC connection - optional use (included) 5. Setting up

8 Setting up using batteries: Important: To avoid operating problems, please take note of battery polarity if inserting any batte

9 Setting up using the AC adaptor: 1) Power up all the sensors as described in setting up using batteries above 2) Using the AC adaptor (included),