La Crosse Technology 616-146 Einstellungsanleitung PDF herunterladen

INTRODUCTION:

The Atomic Projection Alarm features radio-controlled time, indoor and outdoor

temperature on a stylish, colorful, and easy to read display. Time and/or outdoor

temperature can be projected on a wall or ceiling. Use the integrated USB charging

port to charge your devices when the Projection Alarm is plugged into a power

outlet.

ATOMIC PROJECTION ALARM:

SETUP INSTRUCTIONS STEP BY STEP:

STEP 1:

 Remove battery cover from Projection Alarm, slide tab up and pull out to remove

the cover.

 Insert 2 NEW AA batteries (not included)

into the back of the Projection Alarm.

Observe the correct polarity (see marking

inside the battery compartment).

 Do NOT mix old and new batteries.

 The Projection Alarm will light up and

display, indoor temperature and time

(12:00).

STEP 2:

 Insert the 5 volt AC power adapter into the

designated area on the back of the Projection Alarm.

 Insert the power adapter plug into a wall outlet for a continuous backlight.

 IMPORTANT: When operating on a/c power, to avoid interference, the backlight,

projection and USB charge port, will turn off while the Projection Alarm searches

for the WWVB signal. The backlight, projection and USB charge port will function

again after the 2-10 minute search .

STEP 3:

 Ensure that the outdoor transmitter is within 10 feet of the Projection Alarm during

setup.

 Remove battery cover from transmitter: Slide the battery

cover down and lift off the back.

 Insert 2 NEW AA batteries into the TX14 transmitter.

Observe the correct polarity.

 Keep the Projection Alarm and the transmitter close to each

other (within 10 feet).

 Within 3 minutes the Projection Alarm will beep and then

display readings in the Outdoor temperature area.

TROUBLESHOOTING:

 If the Projection Alarm does not display the outdoor temperature after 3 minutes,

remove the a/c power adapter and all batteries from both units and start the setup

process again.

 If the outdoor temperature does not show up after a second attempt, please slide

open the battery cover of the outdoor transmitter to reveal the TX button push

down on the TX button for 3 seconds to send a wireless signal to the Projection

Alarm.

 Hold the +/TEMP button and the Projection Alarm will search for the transmitter.

 For optimal 433 MHz reception, the outdoor transmitter should be placed within

200 feet (60 meters) from the Projection Alarm (see positioning outdoor

transmitter).

 Note: Use Alkaline batteries (or Lithium for temperatures below - 20°F / -28.8°C).

WWVB RADIO CONTROLLED TIME

The NIST radio station, WWVB, is located in Ft. Collins, Colorado and transmits the

exact time signal continuously throughout the United States at 60 kHz. The signal

can be received up to 2,000 miles away through the internal antenna in the Atomic

Projection Alarm. However, due to the nature of the Earth’s Ionosphere, reception is

very limited during daylight hours. The Atomic Projection Alarm will search for a

signal every night when reception is best.

WWVB RECEPTION ICON with full signal strength will appear on screen if the

reception of WWVB signal is successful.

 The tower icon is solid when the Projection Alarm has received the WWVB signal.

 The tower icon will flash when searching for a signal.

 No tower icon displayed. The Projection Alarm was unable to receive a signal at

this time.

 Reposition the Projection Alarm for better signal reception or try again at bedtime.

 Hold the -/TIME button to force a signal search at night when reception is best.

 The Projection Alarm will start searching at UTC: 07:00 and if no reception on the

first attempt they will try again at 0800, 0900 and 1000. Each attempt will be at

least 2 minutes and the most will be 10 min.

 If there is no signal or too much interference the receiver will only be on for 2

minutes.

 If the signal is good it may catch a signal in ABOUT 2-3 minutes. If the signal is

marginal it will try to catch a signal for up to 10 minutes.

 IMPORTANT: When operating on a/c power, to avoid interference, the backlight,

projection and USB charge port, will turn off while the Projection Alarm searches

for the WWVB signal. The backlight, projection and USB charge port will function

again after the 2-10 minute search which occurs during the late night or early

morning hours.

Note: In case the Atomic Projection Alarm is not able to detect the WWVB signal

(disturbances, transmitting distance, etc.); the time can be manually set.

BUTTON FUNCTIONS:

Button

Press and Release

Functions

Hold 2 seconds

SET/°C/°F

Move through program menu

(setup)

Select temperature in °C/°F

Enter program menu, Set

time, date, etc. (setup)

ALARM

Once: View Alarm

Twice: Activate or Deactivate

Alarm

Alarm set

+/TEMP

1 step forward (setup)

Search for Transmitter

Fast advance (setup)

-/TIME

1 step backward (setup)

Fast backward ( setup)

WWVB Search

PROJECTION

Rotate Projection 90 degrees

Change what is projected:

Time/Outdoor Temp

alternating (default)

Once: Time only

Twice: Outdoor Temp

only

Third time: Time/Outdoor

Temp alternating (default)

SNOOZE/LIGHT

HI/LOW/OFF

Once: Backlight/Projection

low intensity (a/c)

Twice: Backlight/Projection

OFF (a/c)

3rd time: Backlight/Projection

ON high intensity (default,

a/c)

Activate backlight/projection

10 seconds (battery power)

Trigger snooze (alarm

active)

PROGRAM MENU:

The SET/°C/°F button will move through the program menu. The +/TEMP or -/TIME

buttons will change a value.

 WWVB ON/OFF: Hold the SET/°C/°F button 5 seconds and WWVB and the word

ON will flash. Press and release the +/TEMP or -/TIME button to turn this to OFF

if you do not wish WWVB reception. Confirm with the SET/°C/°F button and move

to the next item.

 TIME ZONE: EST will flash. Press and release the +/TEMP or -/TIME button to

select a different Time Zone: AST=Atlantic, EST= Eastern, CST= Central, MST=

Mountain, PST= Pacific, AKT= Alaska, HAT=Hawaiian time zone. Confirm with the

SET/°C/°F button and move to the next item.

 DAYLIGHT SAVING TIME: DST will flash and the word ON. Press and release

the +/TEMP or -/TIME button to turn this to OFF if you do not observe DST.

Confirm with the SET/°C/°F button and move to the next item.

 12/24 HOUR TIME: 12H will flash. Press and release the +/TEMP or -/TIME

button to select 24H. Confirm with the SET/°C/°F button and move to the next

item.

 HOUR: The hour will flash. Press and release the +/TEMP or -/TIME button to

select the correct hour. Confirm with the SET/°C/°F button and move to the next

item.

 MINUTES: The minutes will flash. Press and release the +/TEMP or -/TIME button

to select the correct minutes. Confirm with the SET/°C/°F button and move to the

next item.

 YEAR: The year will flash. Press and release the +/TEMP or -/TIME button to

select the correct year. Confirm with the SET/°C/°F button and move to the next

item.

 MONTH: The month will flash. Press and release the +/TEMP or -/TIME button to

select the correct month. Confirm with the SET/°C/°F button and move to the next

item.

 DATE: The date will flash. Press and release the +/TEMP or -/TIME button to

select the correct date. Confirm with the SET/°C/°F button and exit the program

menu.

 Note: The Day of the Week will SET automatically after the year, month and date

are set.

FAHRENHEIT/CELSIUS: Press and release the SET/°C/°F button to select

temperature readings in Fahrenheit or Celsius.

ALARM SET:

 ALARM HOUR: Hold the ALARM button to enter alarm time setting mode. The

Alarm Hour will flash. Use the +/TEMP or -/TIME button to Set the Hour. Press

and release the ALARM button.

 ALARM MINUTE: The Alarm Minutes will flash. Use the +/TEMP or -/TIME button

to Set the Minutes. Press and release the ALARM button to exit.

ALARM ACTIVATION: ALARM ICON

 Press and release the ALARM button once to show Alarm Time.

 With the Alarm time showing, press and release the ALARM button to activate the

alarm. The alarm icon appears when alarm is activated.

 With the Alarm time showing, press and release the ALARM button to deactivate

the alarm. The alarm icon will disappear when alarm is activated.

SNOOZE:

 When the alarm sounds, press the SNOOZE button to trigger snooze alarm for 9

minutes. The snooze icon Zz will flash when the snooze feature is active.

 To stop alarm for one day, press AL button, while in snooze mode. The alarm icon

will remain solid.

BACKLIGHT AND PROJECTION INTENSITY: Press and release the

SNOOZE/LIGHT button to adjust the brightness of the backlight and projection

(together):

 ON High intensity: The backlight and projection are defaulted to HI when the

Adapter is in use.

 ON Low intensity: Press and release SNOOZE/LIGHT button once

 OFF: Press and release SNOOZE/LIGHT button

 ON High intensity (default): Press and release SNOOZE/LIGHT button

 Note: When the Adapter is NOT in use, the High/Low/On/Off features are not

available.

Atomic Projection Alarm

Model: 616-146 | Quick Setup Guide

TIME

O/D TEMP

TREND

ARROW

LOW

BATTERY

PROJECTION

ARM

(ADJUSTABLE)

DATE

I/D TEMP

TREND

ARROW

SNOOZE/LIGHT/HI/LOW/OFF (TOP)

1 2

1
Printed in China 2

Inhaltsverzeichnis

Seite 1 -

INTRODUCTION: The Atomic Projection Alarm features radio-controlled time, indoor and outdoor temperature on a stylish, colorful, and easy to read

Seite 2 - Printed in China

PROJECTION: Battery Power: Press and release the SNOOZE/LIGHT button to show the projection for 10 seconds. Note: Projection will not display constan

Kommentare zu diesen Handbüchern

Keine Kommentare

La Crosse Technology 616-146 Einstellungsanleitung

Stöbern Sie online oder laden Sie Einstellungsanleitung nach Wecker La Crosse Technology 616-146 herunter. La Crosse Technology 616-146 Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Wecker La Crosse Technology 616-146